THUMPER
THUMPER REDARC CLASSIC BATTERY BOX + THUMPER 120AH LiFePO4 + 6M 8MM CIRCUIT BREAKER LOOM + BATTERY BOX TRAY
THUMPER REDARC CLASSIC BATTERY BOX + THUMPER 120AH LiFePO4 + 6M 8MM CIRCUIT BREAKER LOOM + BATTERY BOX TRAY
SKU:BBRCLASSIC+TL-120+LCB+T
Built with the Redarc BCDC25D DC charger |
Designed to suit new model vehicles with smart / variable alternators |
Also compatible with older model vehicles |
Will increase low voltage output from vehicle output to allow battery to reach 100% |
Will act to isolate from the vehicle's main battery once ignition has been switched off |
Designed with an independent Anderson connector for vehicle input |
Designed with an independent Anderson connector for solar panel input (regulated connection - up to 400-450watts of solar) |
Internally wired and protected with circuit breaker protection, allowing for an easy connection direct to the battery |
Equipped with multiple outlet sockets for running 12 Volt appliances |
Available in multiple packages with and without wiring looms / mounting trays and battery. |
This particular model suits a DUAL CHEMISTRY of both Lithium & AGM:
1 |
Redarc BCDC1225D 25Amp DC Battery charger (solar and vehicle compatible charge) - suitable for Lithium / Gel / AGM / Calcium |
2 | Marine grade Cigarette socket - rated to 16 Amps Includes rubber cap design to protect all sockets |
1 |
Engel Fridge type socket (2 prong design) - rated to 16 Amps |
1 | Dual USB socket - rated to 2.2Amp (min rating) - used to illuminate the Volt meter gauge and activate the USB |
2 | 50 Amp Anderson connectors - Labelled INPUT/OUTPUT (one fitted to front of box and one on rear) |
1 | 50 Amp Anderson connectors - designed purely for solar panel input - labelled "Unregulated solar input" |
1 | 50 Amp Anderson connectors - designed purely for vehicle (alternator) input - labelled "Alternator input" |
1 | All internal cabling to allow you to simply connect straight to the battery terminals |
1 | 3 year manufacturing warranty |
Length |
330 mm |
Width | 183 mm |
Height | 220 mm (base only - lid allows for further height) |
Length |
410 mm |
Width | 260 mm |
Height | 280 mm |
Thumper Lithium 120AH LiFePO4 Battery
Thumper Lithium LiFePO4 batteries are fully sealed and are designed to be mounted on any angle for easy application.
Equipped with an internal battery management system (BMS), the Thumper Lithium offers safe charging and discharging with over temperature protection, under and over voltage cut off protection and also internal short circuit protection.
The LiFePO4 range of batteries are less than half the weight of a traditional AGM battery, whilst still offering all of the benefits of a heavy duty deep cycle.
These batteries are designed to hold the terminal voltage higher throughout each cycle, resulting in an increase depth of discharge and a longer overall run time with heavier draw appliances.
Features:
• Less than half the weight of a traditional lead acid battery
• Higher voltage maintained for longer run times with appliances
• Proven quality and reliability
• Compatible with chargers with an AGM or lithium setting
• For best results: Use of a lithium charger is recommended
• 5 year warranty
• Increased cycles compared to traditional lead acid
• Designed to be wired as parallel OR series
• Parallel connection is non-limited
• Max series voltage is 48 Volt (max 4 series)
• This battery is NOT designed for starting purposes
• This battery is NOT designed for under bonnet application
Technical Specifications:
Model No. | TL-120P |
Nominal Voltage | 12.8 V |
Rated Capacity | 120 AH |
Cell Type / Chemistry | Prismatic / LiFePO4 |
Dimensions and Weight:
Length | 328 mm |
Width | 172 mm |
Height (Total) | 220 mm |
Weight | 13.8 Kg |
Operating Temperature Range:
BMS High temp cut out / Reconnect | 80˚C / 50˚C |
Discharge | -20˚C ~ 60˚C |
Charge | -20˚C ~ 45˚C |
Storage | -5˚C ~ 35˚C |
Charging Methods:
Recommended Charge Current | 10 ~ 50 Amps |
Max Charge Current | 80 Amps |
Discharge:
Max discharge current (continuous) | 100 Amps |
Peak discharge current (1-3 seconds) | 300 Amps |
BMS Current cut off | >100.5A 10s |
BMS Current cut off | >120.0A 3s |
BMS Current cut off | >150.0A 1s |
BMS Voltage cut off / Reconnect | 10.0V / 12.0V |
Self Discharge per month: | ≤3% |
Warranty | 5 years from date of purchase | as of June 2023 |
LOOM KIT
This cable is designed to allow you to fit your own Anderson connector from your battery.
- Simply mount the Anderson connector (for example on the rear of the vehicle / or on the front of the Caravan A-frame).
- Feed the cable length back to the battery location
- Connect your negative (black wire) directly to the negative of the battery
- Fit the Circuit breaker (provided) in line of the positive (red cable), as close the battery location as possible.
The circuit breaker will act to protect the line (similar to a fuse). If there is a fault on the line, the circuit breaker will 'trip' until the fault has been remedied. It will 'automatically reset' itself once the fault is no longer present.
Specifications:
- Cable = 6 meters of 8mm twin core automotive cable - rated to approx. 75 Amps over 6mt
- Anderson = 50 Amp Genuine Anderson connector (Uni-sex)
- Circuit breaker = 50 Amp automatic reset circuit breaker
THUMPER BATTERY BOX TRAY
The set up comes equipped with 4 x steel 'hold down rods' and locking nuts, which perfectly secure through the side handles of the Thumper box.
As the Thumper box is designed with the 'Quick connect' lid to secure the lid to the battery base, this tray now offers a secure way to fasten your battery base to the vehicle with complete safety in mind.
This introduction to the range allows for a complete set up, which remains easy to remove if and when the need arises.
Code: | BB-TRAY |
Weight: | 686 grams |
Package Includes: | 1 x Battery Tray 4 x Steel Rods with lock nut secured already 4 x Adjustable lock nuts |
Battery Box dimensions to suit box: |
L 332 x W 188mm |